Read the docs

Interrupt storm in Zephyr Renesas RA SCI UART driver hangs the system

Priority LOW 20CWE-835Published · Updated

Key facts

Attack vector
Physical
Privileges required
None
User interaction
None
Attack complexity
Low
Impact type
Denial of service
Confidentiality · integrity · availability
None · None · High
Fix status
Fixed

Attack profile from CVSS 3.1 · CNA. Fix status from CNA. Impact type from CWE-835.

Summary

Zephyr's Renesas RA SCI UART driver enters an endless interrupt loop when the receive-error interrupt is enabled without a registered callback. A receive line error such as overrun, framing, parity or break re-triggers the ISR without end, because the error flags and pending interrupt stay set, and runtime uart_configure() and uart_irq_err_enable() leave the interrupt live without a callback. A peer that asserts a break or sends at a mismatched baud rate triggers it with one frame, and the CPU stays in the handler until an external reset or hardware watchdog fires. The impact is availability only, and the flaw is CWE-835.

Written with Claude Haiku 5.5 from the sources below · 2026-11-10

Description from the CNA

The Renesas RA SCI UART driver's receive-error ISR, uart_ra_sci_eri_isr() in drivers/serial/uart_renesas_ra_sci.c, acknowledged the error condition only when a Zephyr interrupt-driven callback had already been registered. With CONFIG_UART_INTERRUPT_DRIVEN=y and CONFIG_UART_ASYNC_API=n, if data->user_cb is NULL the ISR body is empty: the SCI error flags (SSR.ORER, SSR.FER, SSR.PER) are left set and the ICU event flag R_ICU->IELSR_b[eri_irq].IR is never cleared, so the interrupt re-pends immediately and the ISR is re-entered without end. The error interrupt is masked at boot by uart_ra_sci_init(), but FSP's R_SCI_UART_Open() unconditionally re-enables it, and uart_ra_sci_configure() - the back end of the public uart_configure() API, enabled by default via CONFIG_UART_USE_RUNTIME_CONFIGURE - performs a Close()/Open() pair without re-masking it. Any runtime uart_configure() therefore leaves the error interrupt live regardless of whether a callback has been set, as does calling uart_irq_err_enable() on its own. An instance used with the polling API, or the window between uart_configure() and uart_irq_callback_user_data_set(), thus runs with the error interrupt unmasked and no callback registered. The trigger is an ordinary receive line error - overrun, framing, parity, or a break condition - which is fully determined by the device attached to the serial link. A peer able to assert a break or transmit at a mismatched baud rate produces such an error at will, so a single frame is enough to enter the state. The impact is availability only: the CPU is captured in the re-entering ISR and never returns to thread context, hanging the entire system until an external reset or hardware watchdog fires. There is no memory corruption or information disclosure. Builds using the asynchronous UART API are unaffected, because the fall-through to FSP's sci_uart_eri_isr() clears both the error flags and the pending IRQ.

Why it matters now

Exploitation None reported CISA SSVC · not in CISA KEV
EPSS 0.00156 4th percentileScored 2026-11-16
Fix Fixed zephyr (zephyrproject): 4.3.2, 4.5.0

SSVC decision points

CISA ADP · SSVC 2.0.3

Exploitation
None
Automatable
No
Technical impact
Partial

The decision (Track, Attend, Act) also depends on your mission and well-being impact; see CISA's SSVC guide.

Affected products

VendorProductAffected versionsFixed inStatusSource
zephyrprojectzephyr4.0.0 to before 4.3.2; 4.4.0 to before 4.5.04.3.2, 4.5.0Patch availableCNA
  • zephyr Vendorzephyrproject Affected 4.0.0 to before 4.3.2; 4.4.0 to before 4.5.0 Fixed in 4.3.2, 4.5.0 Patch available CNA

CPE names Threatist (inferred) · 1

Inferred from how NVD named this product before; not given by a source.

CPEVersionsRoleVendor
cpe:2.3:o:zephyrproject:zephyr:*:*:*:*:*:*:*:*——zephyrproject
  • cpe:2.3:o:zephyrproject:zephyr:*:*:*:*:*:*:*:* Versions — — ·zephyrproject

Remediation

Upgrade Zephyr to version 4.3.2 or 4.5.0. The sources list no vendor advisory identifier for this fix.

Written with Claude Haiku 5.5 from the sources below · 2026-11-10

  • Fix · CNA zephyr (zephyrproject) Fixed in 4.3.2, 4.5.0

Fixed in the same release

Records fixed by the same vendor advisory or release, as the CNA lists them.

  • Release ·

    zephyrproject zephyr 4.3.2, 4.5.0

    6 records Highest priority Priority LOW 6 LOW

    Other records, highest priority first

    • TI-2026-87402 Zephyr NXP ENET-QOS Ethernet driver writes to invalid DMA addressPriority LOW 39
    • TI-2026-87397 Uninitialized pointer in Zephyr Xtensa MMU allows out-of-bounds writesPriority LOW 35
    • TI-2026-87401 Permanent transmit loss in NXP ENET QoS driver after link dropPriority LOW 28

Timeline

  1. 2026-11-09 Threatist record created from CVE-2026-90585
  2. 2026-11-12 CISA SSVC decision points changed

References

  • TI-2026-04422 Out-of-bounds read/write in HTTP WebSocket upgrade via non-null-terminated Sec-WebSocket-Key CVSS 3.1CRITICAL 9.8
  • TI-2026-01361 dns: memory‑safety issue in the DNS name parser CVSS 3.1CRITICAL 9.8
  • TI-2026-09174 Unterminated URI buffer causes out-of-bounds read in LwM2M firmware pull (Package URI) CVSS 3.1CRITICAL 9.1
  • TI-2026-09168 Stack buffer overflow in `net_ipaddr_parse()` IPv4 address-with-port parsing in `subsys/net/ip/utils.c` CVSS 3.1CRITICAL 9.8
  • TI-2024-09625 net: lib: http_server: Buffer Under-read CVSS 3.1HIGH 8.6
  • TI-2021-02863 Usb bluetooth device ACL read cb buffer overflow CVSS 3.1CRITICAL 9.6
See all 366 →

Sources

This product uses the NVD API but is not endorsed or certified by the NVD. Sources and licences